Exposure to micro(nano)plastics polymers in water stored in single-use plastic bottles.

Human exposure to micro (nano)plastics (MNPLs) has become a significant concern as a potential health threat. Exposure routes include ingestion, inhalation, and dermal contact, being food and drinking water the primary sources of oral exposure. Here we present the quantification of polymers of MNPLs particles from 700 nm to 20 µm in bottled water commercialised in Spain, including an estimation of the potential risk for daily consumers. We evaluated samples from 20 popular brands in 0.5 and 1.5 L plastic bottles. A double-suspect screening approach developed and validated in our research group for drinking water was adapted for bottled water samples. The identification and quantification of MNPLs-polymers in mass units and the tentative identification of plastic additives (PA) until the second level of confidence was carried out based on high-performance liquid chromatography coupled to high-resolution mass spectrometry (HPLC-HRMS). The results showed the presence of polypropylene (PP), polyethylene (PE) and polypropylene terephthalate (PET) in the samples. Among them, PE was the most frequently detected and quantified polymer (55% of samples) followed by PET which was detected in 33% of the samples and showing the highest concentration (4700 ng L-1). The median value of the sum of polymer concentrations was 359 ng L-1. In addition, 28 plastic additives were detected, where at least one of them was present in 100% of the samples. Stabilizers and plasticisers were the most frequently identified. A prioritisation study was performed using a multi-QSAR modelling software, where bis(2-ethylhexyl) adipate and bis(2-ethylhexyl) phthalate were estimated as the most potentially harmful compounds for human health. Overall, findings suggest that bottled water is a non-negligible route to exposure to MNPLs.

Polymers of micro(nano) plastic in household tap water of the Barcelona Metropolitan Area.

Microplastics (MPLs) are emerging persistent pollutants affecting drinking water systems, and different studies have reported their presence in tap water. However, most of the work has a focus on particles in the 100-5 µm range. Here, a workflow to identify and quantify polymers of micro and nanoplastics (MNPLs), with sizes from 0.7 to 20 µm in tap water, is presented. The analytical method consisted of water fractionated filtration followed by toluene ultrasonic-assisted extraction and size-exclusion chromatography, using an advanced polymer chromatography column coupled to high-resolution mass spectrometry with atmospheric pressure photoionization source with negative and positive ionization conditions (HPLC(APC)-APPI(±)-HRMS) and normal phase chromatography HILIC LUNA® column and electrospray ionisation source in positive and negative mode (HPLC(HILIC)-ESI(±)-HRMS). The acquisition was performed in full scan mode, and the subsequent tentative identification of MNPLs polymers has been based on increasing the confirmation level, including the characterisation of monomers by using Kendrick Mass Defect (KMD) analysis, and confirmation and quantification using standards. This approach was applied to assess MNPLs in tap water samples of the Barcelona Metropolitan Area (BMA), that were collected from August to October 2020 from home taps of volunteers distributed in the 42 postal codes of the BMA. Polyethylene (PE), polypropylene (PP), polyisoprene (PI), polybutadiene (PBD), polystyrene (PS), polyamide (PA), and polydimethylsiloxanes (PDMS) were identified. PE, PP, and PA were the most highly detected polymers, and PI and PBD were found at the highest concentrations (9,143 and 1,897 ng/L, respectively). A principal component analysis (PCA) was conducted to assess differences in MNPLs occurrence in drinking water, that was provided from the two drinking water treatment plants (DWTPs) suppliers. Results showed that no significant differences (at 95% confidence level) were established between the drinking water supplies to the different areas of the BMA.